Friday, April 30, 2021

DIY Raspberry Pi UPS – An Uninterrupted Power Supply to Keep your Pi Safe during Power Failure @Raspberry_Pi #PiDay #RaspberryPi

Raspberry Pi UPS

Great project write-up by Sourav Gupta up on CircuitDigest.

To save the Pi during uncertain power falls or unintended shutdowns, a UPS can be constructed, same as the UPS backups which are used in our home or offices. Here in this project, we will make the RPI UPS power supply that could provide sufficient time to save the code in RPi as well as this can be used as a separate power supply unit for backup also. We have built this project on PCB and have used PCBWay to fabricate the boards for this project. In the following sections of the article, we have covered in detail the complete procedure to design, order, and assemble the PCB boards for this Raspberry Pi UPS Hat from PCBWay so that you can also easily build one on your own. So let’s get started.

Read more.

Plant Rotator #piday #raspberrypi @Raspberry_Pi

Instead of watching your plants lean to one side all day, you can rotate them!

via yoheio on instructables

This is a writeup of a project I did for my Introduction to Making class. I was inspired by my wife who wanted a device that automatically rotates her plant so that each section gets an even distribution of sunlight.

Read more.


3055 06Each Friday is PiDay here at Adafruit! Be sure to check out our posts, tutorials and new Raspberry Pi related products. Adafruit has the largest and best selection of Raspberry Pi accessories and all the code & tutorials to get you up and running in no time!

How To Use CircuitPython on a Raspberry Pi #piday #raspberrypi @Raspberry_Pi

EQWfPwLY4nbn4R5sYCeesW 970 80

A couple simple projects from Les Pounder on Tom’s Hardware demonstrating the power of CircuitPython on the Rasperry Pi:

CircuitPython can also be used on the Raspberry Pi and via two projects we introduce how to use CircuitPython with the Raspberry Pi. The first project is the humble LED, controlling how to blink an LED enables us to understand how we communicate and control components. The second project involves using additional components connected to the GPIO via a jumper wire to Stemma QT connector.

CircuitPython on the Raspberry Pi is transferable to other devices, such as Adafruit’s QT Py RP2040, Feather RP2040 and Pimoroni’s Keybow 2040, along with the Raspberry Pi Pico. So the skills learned here are applicable to any board that can run CircuitPython

Learn more!


3055 06Each Friday is PiDay here at Adafruit! Be sure to check out our posts, tutorials and new Raspberry Pi related products. Adafruit has the largest and best selection of Raspberry Pi accessories and all the code & tutorials to get you up and running in no time!

Installing AnyDesk to the Raspberry Pi #piday #raspberrypi @Raspberry_Pi

via PiMyLifeUp

AnyDesk is one of the best solutions for adding remote desktop support to your Raspberry Pi.

Using this software, you can remotely access your Raspberry Pi from anywhere in the world using a secure connection.

Unlike TeamViewer for the Raspberry Pi, you can even use this software to remotely manage other devices running the AnyDesk software.

Read more.


3055 06Each Friday is PiDay here at Adafruit! Be sure to check out our posts, tutorials and new Raspberry Pi related products. Adafruit has the largest and best selection of Raspberry Pi accessories and all the code & tutorials to get you up and running in no time!

Ghostbusters PKE Meter #piday #raspberrypi @Raspberry_Pi

Ghostbusters PKE Meter 8 Steps with Pictures Instructables

Track down ghosts with this super authentic PKE meter. If you were a fan of the show growing up, you remember how vital this tool was. From Starscream205 on Instructables:

There was one cartoon in particular that seems to dominate my childhood memories and that was The Real Ghostbusters. Ray, Winston, Peter and Egon were armed to the teeth with really cool gadgets, among them the PKE meter. This was my favourite of all their tech and it basically detected the ghosts they were trying to hunt.

What I am going to do is make my own fully functional PKE meter.

Learn more!


3055 06Each Friday is PiDay here at Adafruit! Be sure to check out our posts, tutorials and new Raspberry Pi related products. Adafruit has the largest and best selection of Raspberry Pi accessories and all the code & tutorials to get you up and running in no time!

Ghostbusters PKE Meter #piday #raspberrypi @Raspberry_Pi

Ghostbusters PKE Meter 8 Steps with Pictures Instructables

Track down ghosts with this super authentic PKE meter. If you were a fan of the show growing up, you remember how vital this tool was. From Starscream205 on Instructables:

There was one cartoon in particular that seems to dominate my childhood memories and that was The Real Ghostbusters. Ray, Winston, Peter and Egon were armed to the teeth with really cool gadgets, among them the PKE meter. This was my favourite of all their tech and it basically detected the ghosts they were trying to hunt.

What I am going to do is make my own fully functional PKE meter.

Learn more!


3055 06Each Friday is PiDay here at Adafruit! Be sure to check out our posts, tutorials and new Raspberry Pi related products. Adafruit has the largest and best selection of Raspberry Pi accessories and all the code & tutorials to get you up and running in no time!

Custom Raspberry Pi Pico-powered WiFi Temperature Sensor #piday #raspberrypi @Raspberry_Pi

David Booth shared their custom temperature sensor using MQTT and CircuitPython.

via raspberry pi pod and micro:bit base

A custom, low power temperature sensor powered by a Raspberry Pi Pico with an LCD display and WiFi connectivity for integration into an MQTT home automation hub.

For a number of years now, I’ve been wanting to monitor room temperatures across my house to assess the effect of multiple heating sources and insulation efficiency. Best practice would dictate that I have multiple sensors running in parallel to get data points that are relative to one another. For multiple sensors to be running constantly, I’d prefer it to be low powered and low cost to maximise the number of units I can have in the setup. For ease of setup, it would be preferable for each unit to be wireless to allow temperature data collection to be performed in a single location and for each unit to only require a power connection.

Read the full project here.


3055 06Each Friday is PiDay here at Adafruit! Be sure to check out our posts, tutorials and new Raspberry Pi related products. Adafruit has the largest and best selection of Raspberry Pi accessories and all the code & tutorials to get you up and running in no time!

IoT Twitter Follower Tracker and Status Notifier @Raspberry_Pi #PiDay #RaspberryPi

TIarNOlTIb blob

Fun build from Kutluhan Aktar up on Hackster.io.

I have a gradually growing Twitter account for my website to showcase my projects and articles. Most of the time, I forget to check if there is a change in the follower count of my Twitter account to discern the account growth chronologically. Thus, I decided to create this apparatus placed on my desk, which displays information of my Twitter account:

Read more.


3055 06Each Friday is PiDay here at Adafruit! Be sure to check out our posts, tutorials and new Raspberry Pi related products. Adafruit has the largest and best selection of Raspberry Pi accessories and all the code & tutorials to get you up and running in no time!

The Kay-Berlin Food Computer @Raspberry_Pi #PiDay #RaspberryPi

“Food Computer” may be a bit misleading as a description for this project. The machine is less like a computing machine made from tasty snacks, and more like a fully-automated plant growth station. Here’s more from Raspberry Pi Blog:

“It is a fully automated growth chamber that can monitor over a dozen atmospheric and root zone variables and post them to an online dashboard for remote viewing,” Chris Regini tells us. He’s supervising both Noahs in this project. “In addition to collecting data, it is capable of adjusting fan speeds based on air temperature and humidity, dosing hydroponic reservoirs with pH adjustment and nutrient solutions via peristaltic pumps, dosing soil with water based on moisture sensor readings, adjusting light spectra and photoperiods, and capturing real-time and time-lapsed footage using a [Raspberry Pi] Camera Module NoIR in both daylight and night-time growth periods.”

See project!

As Seen on Show & Tell: Sai’s Pico Phone #piday #raspberrypi @Raspberry_Pi

Big thanks to Sai for joining us on Show & Tell and for sending in a link to this awesome project! Cheers to future maker faires! Sai writes:

Here is the link to the Pico Phone project I shared on Show and Tell today:

https://www.hackster.io/diy-champs/pico-phone-c0f1eb

Read all about Sai’s project from Hackster.io and don’t miss the segment on Show & Tell below!


3055 06Each Friday is PiDay here at Adafruit! Be sure to check out our posts, tutorials and new Raspberry Pi related products. Adafruit has the largest and best selection of Raspberry Pi accessories and all the code & tutorials to get you up and running in no time!

Raspberry Pi Dog Detector @Raspberry_Pi #PiDay #RaspberryPi

Who doesn’t like looking at dogs? Ryder over at Ryder Calm Down does. And he’s using Raspberry Pi to up his game. Here’s more from Ryder Calm Down:

Quarantine isn’t great, but looking at dogs makes me feel better. So I built a machine that notifies me when a dog passes in front of my house so I can go look at it.

See more!


3055 06Each Friday is PiDay here at Adafruit! Be sure to check out our posts, tutorials and new Raspberry Pi related products. Adafruit has the largest and best selection of Raspberry Pi accessories and all the code & tutorials to get you up and running in no time!

Thursday, April 29, 2021

Pixhawk Raspberry Pi Drone #piday #raspberrypi @Raspberry_Pi

Learn how to make a Drone with Pixhawk and Raspberry Pi from The Drone Dojo on YouTube, via The Drone Girl:

In this video we walk through how to set up a drone with the very popular pixhawk flight controller!

See more


3055 06Each Friday is PiDay here at Adafruit! Be sure to check out our posts, tutorials and new Raspberry Pi related products. Adafruit has the largest and best selection of Raspberry Pi accessories and all the code & tutorials to get you up and running in no time!

Raspberry pi no ir camera mount #3Dprinting #3DThursday

Raspberry pi no ir camera mount by Gcode Art Thingiverse

Gcode_Art shared this project on Thingiverse!

The best mount for the no ir raspberry pi camera!!

Download files: https://www.thingiverse.com/thing:3138571


649-1
Every Thursday is #3dthursday here at Adafruit! The DIY 3D printing community has passion and dedication for making solid objects from digital models. Recently, we have noticed electronics projects integrated with 3D printed enclosures, brackets, and sculptures, so each Thursday we celebrate and highlight these bold pioneers!

Have you considered building a 3D project around an Arduino or other microcontroller? How about printing a bracket to mount your Raspberry Pi to the back of your HD monitor? And don’t forget the countless LED projects that are possible when you are modeling your projects in 3D!

Key Holder #3DPrinting #3DThursday

Key Holder by mpgreenough1986 Thingiverse

mpgreenough1986 shared this project on Thingiverse!

Hi all,

Just a simple multilevel Hexagonal Key tidy.

There are 3 heights of key fob to match the varying heights of the holder. Below are the quantities of each you would need to print to fill the holder but I think it looks better if you leave some gaps

Download files: https://www.thingiverse.com/thing:4775253


649-1
Every Thursday is #3dthursday here at Adafruit! The DIY 3D printing community has passion and dedication for making solid objects from digital models. Recently, we have noticed electronics projects integrated with 3D printed enclosures, brackets, and sculptures, so each Thursday we celebrate and highlight these bold pioneers!

Have you considered building a 3D project around an Arduino or other microcontroller? How about printing a bracket to mount your Raspberry Pi to the back of your HD monitor? And don’t forget the countless LED projects that are possible when you are modeling your projects in 3D!

MagSafe Stand #3Dprinting #3DThursday

MagSafe Stand by ZeligD Thingiverse

ZeligD shared this project on Thingiverse!

A revised version of my previous MagSafe Charging Stand

Near exact measurements were used so results may vary depending on your printer 🙂

Download files: https://www.thingiverse.com/thing:4767446


649-1
Every Thursday is #3dthursday here at Adafruit! The DIY 3D printing community has passion and dedication for making solid objects from digital models. Recently, we have noticed electronics projects integrated with 3D printed enclosures, brackets, and sculptures, so each Thursday we celebrate and highlight these bold pioneers!

Have you considered building a 3D project around an Arduino or other microcontroller? How about printing a bracket to mount your Raspberry Pi to the back of your HD monitor? And don’t forget the countless LED projects that are possible when you are modeling your projects in 3D!

Manual Number / Life / Score Counter #3DThursday #3DPrinting

Manual Number Life Score Counter by MuchMore Thingiverse

For when your fingers just won’t cut it. From MuchMore on Thingiverse:

An good working manual counter. I made this for a friend, no idea for what board game he is using it.

Important !! print with a 0.5mm line width (or 0.333mm or 1.0mm), otherwise the spring will not print correct


Edit: now there are two version of the number ring. one going up and one down
Edit_2: now there is a version with 4 digits

Download the files and learn more


649-1
Every Thursday is #3dthursday here at Adafruit! The DIY 3D printing community has passion and dedication for making solid objects from digital models. Recently, we have noticed electronics projects integrated with 3D printed enclosures, brackets, and sculptures, so each Thursday we celebrate and highlight these bold pioneers!

Have you considered building a 3D project around an Arduino or other microcontroller? How about printing a bracket to mount your Raspberry Pi to the back of your HD monitor? And don’t forget the countless LED projects that are possible when you are modeling your projects in 3D!

Rounded Corner Template #3DThursday #3DPrinting

Rounded Corner Template by drphysics Thingiverse

Add a set of these to your tool chest. From drphysics on Thingiverse:

These templates allow you to mark rounded corners for 1/2″, 3/4″, 1″, and 1.5″ corner radii. Hook the template over the corner and mark with a sharp pencil. Then saw and sand to the line. I have also included a four-in-one template.

Download the files and learn more


649-1
Every Thursday is #3dthursday here at Adafruit! The DIY 3D printing community has passion and dedication for making solid objects from digital models. Recently, we have noticed electronics projects integrated with 3D printed enclosures, brackets, and sculptures, so each Thursday we celebrate and highlight these bold pioneers!

Have you considered building a 3D project around an Arduino or other microcontroller? How about printing a bracket to mount your Raspberry Pi to the back of your HD monitor? And don’t forget the countless LED projects that are possible when you are modeling your projects in 3D!

Complete prosthetic arm for hackberry hand #3DThursday #3DPrinting

enablefrance shares:

Complete arm for Hackberry Hand

The arm has been created by a group of e_nable France Makers, for Gaspard15 year old boy born without left arm.
He can activate the hackberry fingers with a mobile bone raising up from his shoulder.

The arm is mechanical
The shoudler is using a lockable joint ball,
The elbow is using a ball_lock rotation
All mechanical locks commands are on the forearm to be easy to access from the right hand.

download the files on: https://www.thingiverse.com/thing:4765775


649-1
Every Thursday is #3dthursday here at Adafruit! The DIY 3D printing community has passion and dedication for making solid objects from digital models. Recently, we have noticed electronics projects integrated with 3D printed enclosures, brackets, and sculptures, so each Thursday we celebrate and highlight these bold pioneers!

Have you considered building a 3D project around an Arduino or other microcontroller? How about printing a bracket to mount your Raspberry Pi to the back of your HD monitor? And don’t forget the countless LED projects that are possible when you are modeling your projects in 3D!

Slider Volume Mixer #3DThursday #3DPrinting

Slider volume mixer deej by KDY0523 Thingiverse

Colorful audio mixer shared by KDY0523 on Thingiverse:

It works perfectly, and it’s easy to assemble.

Working vedio : https://youtu.be/wCOqZlOfDsg

All the info about the original project : https://github.com/omriharel/deej

Download the files and learn more


649-1
Every Thursday is #3dthursday here at Adafruit! The DIY 3D printing community has passion and dedication for making solid objects from digital models. Recently, we have noticed electronics projects integrated with 3D printed enclosures, brackets, and sculptures, so each Thursday we celebrate and highlight these bold pioneers!

Have you considered building a 3D project around an Arduino or other microcontroller? How about printing a bracket to mount your Raspberry Pi to the back of your HD monitor? And don’t forget the countless LED projects that are possible when you are modeling your projects in 3D!

Raspberry Pi Wall Holder (with 40mm Fan) #3Dprinting #3Dthursday

Raspberry Pi Wall Holder with 40mm Fan by ei23 Thingiverse

ei23 shared this project on Thingiverse!

This can be used for Raspberry Pi 4B / 3B / 3B+
With a 40mm fan for cooling.
Keeps temperature of a Pi 4B unter 40°C

Download files: https://www.thingiverse.com/thing:4772033


649-1
Every Thursday is #3dthursday here at Adafruit! The DIY 3D printing community has passion and dedication for making solid objects from digital models. Recently, we have noticed electronics projects integrated with 3D printed enclosures, brackets, and sculptures, so each Thursday we celebrate and highlight these bold pioneers!

Have you considered building a 3D project around an Arduino or other microcontroller? How about printing a bracket to mount your Raspberry Pi to the back of your HD monitor? And don’t forget the countless LED projects that are possible when you are modeling your projects in 3D!

Circle Lamp #3DThursday #3DPrinting

OC lamp by PLENUE Thingiverse

Futuristic mod ring light shared by PLENUE on Thingiverse:

Just like my previous work, I use 5050LED and need some glue to assemble.
5050LED
The length of the 5050 LED is 1m and ip20 no waterproof

Download the files and learn more


649-1
Every Thursday is #3dthursday here at Adafruit! The DIY 3D printing community has passion and dedication for making solid objects from digital models. Recently, we have noticed electronics projects integrated with 3D printed enclosures, brackets, and sculptures, so each Thursday we celebrate and highlight these bold pioneers!

Have you considered building a 3D project around an Arduino or other microcontroller? How about printing a bracket to mount your Raspberry Pi to the back of your HD monitor? And don’t forget the countless LED projects that are possible when you are modeling your projects in 3D!

Component Holder Extendable #3DPrinting #3DThursday

Component Holder Extendable by dsEngineering Thingiverse

dsEngineering shared this project on Thingiverse!

Wanted to make a component holder for electrical components and screws, nuts, etc. which isn’t too big nor small. The frame is extendable “infinitly” and 5 different boxes come with it:

Download files: https://www.thingiverse.com/thing:4769481


649-1
Every Thursday is #3dthursday here at Adafruit! The DIY 3D printing community has passion and dedication for making solid objects from digital models. Recently, we have noticed electronics projects integrated with 3D printed enclosures, brackets, and sculptures, so each Thursday we celebrate and highlight these bold pioneers!

Have you considered building a 3D project around an Arduino or other microcontroller? How about printing a bracket to mount your Raspberry Pi to the back of your HD monitor? And don’t forget the countless LED projects that are possible when you are modeling your projects in 3D!

M3TAL Cyberdeck #3DThursday #3DPrinting

M3TAL Cyberdeck by BlastoSupreme Thingiverse

I feel like all Cyberdecks should a floppy drive. Via BlastoSupreme on Thingiverse:

Hi Everyone! BlastoSupreme here with another Cyberdeck for your building pleasure. This deck is based off of 2020 aluminum extrusion, and is super modifiable and customizable! Features include; floppy drive, RetroCart, 10.1″ screen, 26650 batteries, hardwired mechanical keyboard, carry handle, and more!

This deck does require fairly good soldering skills for the keyboard. Feel free to ask me any questions you may have on twitter @BlastoSupreme or in the cyberdeck Discord.

Full writeup can be found at: https://cyberdeck.cafe/mix/m3tal

Download the files and learn more


649-1
Every Thursday is #3dthursday here at Adafruit! The DIY 3D printing community has passion and dedication for making solid objects from digital models. Recently, we have noticed electronics projects integrated with 3D printed enclosures, brackets, and sculptures, so each Thursday we celebrate and highlight these bold pioneers!

Have you considered building a 3D project around an Arduino or other microcontroller? How about printing a bracket to mount your Raspberry Pi to the back of your HD monitor? And don’t forget the countless LED projects that are possible when you are modeling your projects in 3D!

Medieval style wall light #3DPrinting #3DThursday

Medieval style wall light by Zitouni Thingiverse

Zitouni shared this project on Thingiverse! Download files here: https://www.thingiverse.com/thing:4769533


649-1
Every Thursday is #3dthursday here at Adafruit! The DIY 3D printing community has passion and dedication for making solid objects from digital models. Recently, we have noticed electronics projects integrated with 3D printed enclosures, brackets, and sculptures, so each Thursday we celebrate and highlight these bold pioneers!

Have you considered building a 3D project around an Arduino or other microcontroller? How about printing a bracket to mount your Raspberry Pi to the back of your HD monitor? And don’t forget the countless LED projects that are possible when you are modeling your projects in 3D!

Chatting with the Ruiz Brothers @videopixil @ecken via @hacksterio

We had a super awesome time chatting with Alex Glow about 3D printing, CircuitPython and all of the things in between. Be sure to subscribe to Hackster IO for future livestreams!

Alex Glow on Twitter
Hackster on YouTube

Noé and Pedro Ruiz have created countless tutorials for Adafruit. Their recent companion bot, Terrako, caught our eye – and once we started looking, we found cosplay pieces, LED art, MIDI controllers, and more! We sit down with the brothers to learn more about their creations.

// https://learn.adafruit.com/terrako​
// https://learn.adafruit.com/users/pixil3d​
// Pedro: https://twitter.com/videopixil​
// Noé: https://twitter.com/ecken

New Guide! Lemon Keypad with QT Py RP2040 @ecken @videopixil

DIY USB-HID With a Twist of Lime
Make a custom USB-HID keypad in the shape of a citrus fruit. This keypad features six mechanical switches for controlling media players like Spotify, iTunes, YouTube, etc. Powered by the Adafruit QT Py RP2040 and CircuitPython.

LearnGuide
https://learn.adafruit.com/qtpy-lemon-mechanical-keypad-macropad/overview

Layer by Layer – Fuzzy Skin
https://youtu.be/89oRp64lFfU

QT Py RP2040
https://www.adafruit.com/product/4900

Kailh Mechanical Key Switches
https://www.adafruit.com/product/4955

NeoPixel Jewel
https://www.adafruit.com/product/2226

Inside the case is a NeoPixel Jewel that slowly fades in and out making the keypad illuminate. The QT Py and NeoPixel are housed in a 3D printed case with part that snap fit together.

Lemon, Lime and Fruits
The case and key caps can be 3D printed in different colors. Choose a color scheme that best matches your preferred flavor of fruit. Could it be an orange, a lemon, a lime or maybe a watermelon? You decide!

Kailh Mechanical Key Switches
Click, click, click… Mechanical key switches offer a tactile feeling and there’s a few varieties of switch type. Choose the type that best suits your preference.

Custom Keys

One of the goals of this project was to create a unique layout for a keypad. Originally conceived as a circular keypad, the enclosure evidently turned into a fruit inspired shape. As a result, the key caps are cute little triangular pieces.


649-1
Every Thursday is #3dthursday here at Adafruit! The DIY 3D printing community has passion and dedication for making solid objects from digital models. Recently, we have noticed electronics projects integrated with 3D printed enclosures, brackets, and sculptures, so each Thursday we celebrate and highlight these bold pioneers!

Have you considered building a 3D project around an Arduino or other microcontroller? How about printing a bracket to mount your Raspberry Pi to the back of your HD monitor? And don’t forget the countless LED projects that are possible when you are modeling your projects in 3D!

The Adafruit Learning System has dozens of great tools to get you well on your way to creating incredible works of engineering, interactive art, and design with your 3D printer! If you’ve made a cool project that combines 3D printing and electronics, be sure to let us know, and we’ll feature it here!



Flexi Hermit Crab #3DThursday #3DPrinting

Flexi Hermit Crab
DESSEN
https://cults3d.com/en/3d-model/game/hermit-crab-flexi-cute-semi-realistic
CR10S Pro
Rainbow PLA
14hr 15mins
X:246 Y:189 Z:121mm
.2mm layer / .4mm nozzle
10% Infill / 6mm retract
210C / 60C
20g
90mm/s


649-1
Every Thursday is #3dthursday here at Adafruit! The DIY 3D printing community has passion and dedication for making solid objects from digital models. Recently, we have noticed electronics projects integrated with 3D printed enclosures, brackets, and sculptures, so each Thursday we celebrate and highlight these bold pioneers!

Have you considered building a 3D project around an Arduino or other microcontroller? How about printing a bracket to mount your Raspberry Pi to the back of your HD monitor? And don’t forget the countless LED projects that are possible when you are modeling your projects in 3D!

Pi Pico project solar power charger box #3DThursday #3DPrinting

Fluby shares:

I wanted to power my pico projects free from the mains, but also bring the unit indoors to either program or charge.

download the files on: https://www.thingiverse.com/thing:4769526


649-1
Every Thursday is #3dthursday here at Adafruit! The DIY 3D printing community has passion and dedication for making solid objects from digital models. Recently, we have noticed electronics projects integrated with 3D printed enclosures, brackets, and sculptures, so each Thursday we celebrate and highlight these bold pioneers!

Have you considered building a 3D project around an Arduino or other microcontroller? How about printing a bracket to mount your Raspberry Pi to the back of your HD monitor? And don’t forget the countless LED projects that are possible when you are modeling your projects in 3D!